- 您现在的位置：买卖IC网 > Sheet目录514 > SI8417DB-T2-E1 (Vishay Siliconix)MOSFET P-CH 12V 14.5A 2X2 6MFP
AN824
Vishay Siliconix
Board pad design. The landing-pad size for MICRO FOOT
products is determined by the bump pitch as shown in Table 3.
The pad pattern is circular to ensure a symmetric,
barrel-shaped solder bump.
TABLE 3
Dimensions of Copper Pad and Solder Mask
Opening in PCB and Stencil Aperture
Solder Mask Stencil
Pitch Copper Pad Opening Aperture
Chip pick-and-placement. MICRO FOOT products can be
picked and placed with standard pick-and-place equipment.
The recommended pick-and-place force is 150 g. Though the
part will self-center during solder reflow, the maximum
placement offset is 0.02 mm.
Reflow Process . MICRO FOOT products can be assembled
using standard SMT reflow processes. Similar to any other
package, the thermal profile at specific board locations must
be determined. Nitrogen purge is recommended during reflow
operation. Figure 6 shows a typical reflow profile.
0.80 mm
0.50 mm
0.30 " 0.01 mm
0.17 " 0.01 mm
0.41 " 0.01 mm
0.27 " 0.01 mm
0.33 " 0.01 mm
in ciircle aperture
0.30 " 0.01 mm
in square aperture
250
Thermal Profile
200
ASSEMBLY PROCESS
MICRO FOOT products’ surface-mount-assembly operations
include solder paste printing, component placement, and
solder reflow as shown in the process flow chart (Figure 5).
150
100
50
Stencil Design
IIncoming Tape and Reel Inspection
0
Solder Paste Printing
0
100
200
Time (Seconds
300
400
Chip Placement
Reflow
Solder Joint Inspection
Pack and Ship
FIGURE 5. SMT Assembly Process Flow
FIGURE 6. Reflow Profile
PCB REWORK
To replace MICRO FOOT products on PCB, the rework
procedure is much like the rework process for a standard BGA
or CSP, as long as the rework process duplicates the original
reflow profile. The key steps are as follows:
Stencil design . Stencil design is the key to ensuring
maximum solder paste deposition without compromising the
assembly yield from solder joint defects (such as bridging and
extraneous solder spheres). The stencil aperture is dependent
on the copper pad size, the solder mask opening, and the
quantity of solder paste.
In MICRO FOOT products, the stencil is 0.125-mm (5-mils)
thick. The recommended apertures are shown in Table 3 and
are fabricated by laser cut.
Solder-paste printing. The solder-paste printing process
involves transferring solder paste through pre-defined
apertures via application of pressure.
In MICRO FOOT products, the solder paste used is UP78
No-clean eutectic 63 Sn/37Pb type3 or finer solder paste.
Document Number: 71990
06-Jan-03
1.
2.
3.
4.
5.
6.
Remove the MICRO FOOT device using a convection
nozzle to create localized heating similar to the original
reflow profile. Preheat from the bottom.
Once the nozzle temperature is +190 _ C, use tweezers to
remove the part to be replaced.
Resurface the pads using a temperature-controlled
soldering iron.
Apply gel flux to the pad.
Use a vacuum needle pick-up tip to pick up the
replacement part, and use a placement jig to placed it
accurately.
Reflow the part using the same convection nozzle, and
preheat from the bottom, matching the original reflow
profile.
www.vishay.com
3
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SI8439DB-T1-E1
MOSFET P-CH 8V D-S MICROFOOT
SI8441DB-T2-E1
MOSFET P-CH 20V 10.5A 2X2 6MFP
SI8447DB-T2-E1
MOSFET P-CH D-S 20V MICROFOOT
SI8461DB-T2-E1
MOSFET P-CH D-S 20V MICROFOOT
SI8465DB-T2-E1
MOSFET P-CH D-S 20V MICROFOOT
SI8800EDB-T2-E1
MOSFET N-CH D-S 20V MICROFOOT
SI9407BDY-T1-E3
MOSFET P-CH 60V 4.7A 8-SOIC
SI9433BDY-T1-GE3
MOSFET P-CH D-S 20V 8-SOIC
相关代理商/技术参数
SI84-180
制造商:DELTA 制造商全称:Delta Electronics, Inc. 功能描述:SMT Power Inductor
SI84-180K
制造商:DELTA 制造商全称:Delta Electronics, Inc. 功能描述:SMT Power Inductor
SI84-181
制造商:DELTA 制造商全称:Delta Electronics, Inc. 功能描述:SMT Power Inductor
SI84-181K
制造商:DELTA 制造商全称:Delta Electronics, Inc. 功能描述:SMT Power Inductor
SI8419DB-T1-E1
功能描述:MOSFET 8.0V 11.7A 6.25W 35mohm @ 4.5V RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI8420
制造商:SILABS 制造商全称:SILABS 功能描述:SINGLE & DUAL-CHANNEL DIGITAL ISOLATORS
Si8420AB-C-IS
功能描述:隔离器接口集成电路 Dual Ch 2.5kV Isolator 1M 2/0 RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube
Si8420AB-C-ISR
功能描述:隔离器接口集成电路 DualCh 2.5kV Isolatr 1M 2/0
RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube